IndiaBizClub Login

x Register Free
x Register Free

indus industries pvt.ltd.

J

indus industries pvt.ltd.

Joint Compound

Faridabad



A Quality Product from
indus industries pvt.ltd. [View Profile]
faridabad - India

Description :
Jointing Compound (Gypsum Plaster Board)
Gypsum Plaster Board Joint Fill-N-Finish Compound

This product has been specially formulated as gypsum board jointing compound in powder form, used for jointing & finishing inside the building as per standard recommended practice. It has been formulated as per International standard to have more user friendly features. It is an air drying material & has been formulated to suit tropical climatic & varied site working conditions. It also attains early strength & allows early decoration.
It is in off white fine powder form consisting of all natural ingredients & polymers. It,s density is app. 1100 kg/m3 & powder water ratio is 100:45. If required powder water ratio can be modified suitably depending upon users need.
It,s open time is 100 minutes and final hardening time is 200 minutes. It qualifies tape adhesion test & having good workability. After complete drying, it can be fine sanded & cleaned before surface decoration. It is free from shrinkage cracks.
It is available in 25 kg paper sacks.
Jointing & Finishing
Powder jointing compound is thoroughly mixed to clean water in clean bucket as per powder water ratio to have right consistency paste. The same is left for 5 minutes before it is remixed thoroughly to have paste ready for use.
The paste can be used for Jointing & finishing of both tapered as well as in square edges of board. The joints of boards can be filled & finished with this paste using joint tape as stated below:
Tapered edge boards:
First application
? To fill the joint with the paste of jointing compound so prepared.
? To embed 48mm wide joint fiber tape into centre of the joint, with mild pressure to ensure that the tape is firmly placed in to position.
? To make sure that joint fiber tape is free from trapped air / bubbles & sufficient compound is remain under & above joint tape to ensure good adhesion with board surface. Surplus material should be removed using applicator. To feather out joint edges to remove extra material if left any, and allow to dry.
Second application
? When the first coat application is dried, to apply second coat of the paste of jointing compound to the joint in thin coat with applicator. This is finishing coat application & should be applied carefully but wider than the first coat application.
? To feather out joint edges to remove extra material if left any, and allow to dry.
Third application
? When the 2nd coat is dried, to apply third coat of the paste of jointing compound to the joint in very thin coat with applicator. This is final finishing coat application & should be applied carefully but wider than the previous coat application.
? To ensure that the all three applications are merged & finished nicely. Joint fibre tape is completely covered & each subsequent application is wider than the previous as to look spread over as to hide visibility of the joint.
? To feather out joint edges to remove extra material if left any, and allow to dry.
? Sand the joint with emery paper to get an even surface.

Square edge Boards:
? To fill the gap between the boards and ?V? groove formed by chamfering the board edges with paste of jointing compound and allow it to dry completely.
? To follow the standard steps of J&F as stated above.
? To make sure that the width of the joints so finished as above should be as wide as 4? in stage -1, 6? in stage -2 and 8?? at stage -3. This will help to overcome the visibility of joints due to reflection of light. The less wide joint will be more visible than the wider one.
Corners:
Joint fiber tape should be used by folding it from its centre making it in angle shape (24x24mm) to accommodate both sides of the corners. This folded tape is embedded at corners by using jointing compound as described above.
Nail / screw finishing:
? Nail screw heads should be just below the surface of the board and should not be driven too deep. Recommended screws are to be used for fixing boards. To make sure that all screw heads are inside or in level of board surface.
? All nail / screw heads are to be covered with the paste jointing compound twice to achieve better finished surface.
NOTE:
? Please make sure the screws are sufficiently secured & properly driven. There should not be any movement between the board and metal frame before starting Jointing & finishing.
? Please make sure that sufficient jointing compound paste is applied between the board surface and joint tape.



features :
Gypsum board fill - n- finish joint compound

Special Offer :
Builders & Contractors


View Complete Catalog





indus industries pvt.ltd.

Ready mix Gypsum Plaster, Ready mix White Cement Plaster, Jointing Compound For Gypsum Board, Calcium silicate Board, Cement Particle Board, Ready mix Acrylic Joint Compound, Ready mix Elastomaric Joint Compound, White Cement Putty, Prolite Celing Tiles, Insulation Plaster



View Company Profile

Other Matching Products


Joint Compound

Jointing Compound (Gypsum Plaster Board) Gypsum Plaster Board Joint Fill-N-Finish Compound This product has been specially formulated as gypsum board jointing compound in powd ....

Multi Plus

GYPSOPLAST ? Multi Plus Ready Mix Putty ? Joint Compound GYPSOPLAST - Multi plus - Ready mix putty This Ready mix putty Joint Compound is a re ....

LVL, Windows Scantlings, Construction Timber

Email: info@gdg-plywood.com Web: www.gdg-plywood.com 8)LVL (Laminated Veneered Lumber CORE: Birch, Poplar, Hardwood,Pine GLUE: WBP, MR(E0,E1,E2) JOINT: Overlap-Joint,End-J ....

Joint Pins Rental

services of Joint Pins Rental The company offers Joint Pins Rental Services to meet the specific requirements of the clients. Through Joint Pins Rental Services, customers are e ....

Expansion Joint Filler Board

Bitulex Soft board is processed from cane fibre, the raw material tested and proven to provide the best resilience. Impregnated with Bitumen in various percentages, it is a perfect ....

Bitumen Impregnated Softboard

Jolly Bitulex Softboard is processed from cane fibre, the raw material tested and proven to provide the best resilience. Impregnated with Bitumen in various percentages, it is a pe ....

Waterproofing Systems

ENAQUA: General purpose flexible & tough PU system POLYLAC NY: UV stable PU top coating system ENSEAL 41: Construction joint filling pourable PU compound ENSEAL 61: Thixotrop ....

Joint Compound

It is used for finishing plaster, panel, wallboard joints, no sanding required. Excellent joint compound that can be used indoors & outdoors. Easy to use and paintable. Won't shrin ....

Decoration accessories such as screw etc.

1\Baier screw set company code packing(pieces/box) diameter(mm) BAIER-PST25 1000 2.5 BAIER-PST35 600 3.5 2\Joint Tape Joint Tape With air hole and pre-crease ....

Lap joint flangeball valves

Lap Joint Flanges are similar to slip-on flanges, the difference is it has a curved radius at the bore and face to accommodate a lap joint stub end. The lap joint flange and stub e ....



Business Blog About Us Support Contact Sitemap Privacy Policy Terms & Conditions

© Copyright 2000 - 2017 IndiaBizClub. All rights reserved.